www.berex.com berex, inc. 1735 north 1 st street #302 san jose, ca 95112 tel. (408) 452 - 5595 september 2011 specifications are subject to change without notice. ? berex 2011 rev. 1.2 high efficiency phemt power fet c hip (.25 m x 600 m) the berex bcp060 t is a gaas power phemt w ith a nominal 0. 2 5 micron gate length and 600 micron gate width mak ing the product ideally suited for appl i cations where high - gain and medium power in the 1000 mhz to 26.5 ghz frequency range are required . the product may be used in either wideband (6 - 18 ghz) or narrow - band applications. the BCP060T is produced using state o f the art metallization with si 3 n 4 passivation and is screened to assure reliability . product features ? 2 8 dbm typical output power ? 1 2 db typical gain @ 12 ghz ? 0. 2 5 x 600 micron recessed gate applications ? commercial ? military / hi - rel . ? test & measurement electrical characteristic ( tuned for power ) t a = 25 c symbol parameter/test conditions test freq . min . typical m ax. unit p 1db output power @ p 1db (v ds = 8 v, i ds = 50% i dss ) 12 gh z 18 ghz 27. 0 28.0 28.5 dbm g 1db gain @ p 1db (v ds = 8 v, ids = 50% i dss ) 12 gh z 18 ghz 11.0 12.0 9.0 db pae pae @ p 1db (v ds = 8 v, i ds = 50% i dss ) 12 gh z 18 ghz 55 55 % nf 50 ohm noise figure (v ds =2v, i dss =15 ma) 12 ghz 1.34 db i dss saturated drain current (v gs = 0v, v ds = 2v) 1 2 0 180 2 4 0 ma g m transconductance (v ds = 3v, v gs = 50% i dss ) 240 ms v p pinch - off voltage (i ds = 0.6 m a, v ds = 2v) - 2 .5 - 1.1 - 0.5 v bv gd drain breakdown voltage (ig = 0.6 ma, source open) - 1 5 - 1 2 v bv gs source breakdown voltage (ig = 0.6 ma, drain open) - 1 3 v r th thermal resistance (au - sn eutectic attach) 7 5 c/w BCP060T
www.berex.com berex, inc. 1735 north 1 st street #302 san jose, ca 95112 tel. (408) 452 - 5595 september 2011 specifications are subject to change without notice. ? berex 2011 rev. 1.2 BCP060T electrical characteristic ( tuned for gain ) t a = 25 c symbol parameter/test conditions test freq . min . typical m ax. unit p 1db output power @ p 1db (v ds = 8 v, i ds = 50% i dss ) 12 gh z 18 ghz 27.5 27.0 dbm g 1db gain @ p 1db (v ds = 8 v, ids = 50% i dss ) 12 gh z 18 ghz 11. 0 12.5 9.5 db pae pae @ p 1db (v ds = 8 v, i ds = 50% i dss ) 12 gh z 18 ghz 55 50 % nf 50 ohm noise figure (v ds =2v, i dss =15 ma) 12 ghz 1.34 db i dss saturated drain current (v gs = 0v, v ds = 2v) 1 2 0 180 2 4 0 ma g m transconductance (v ds = 3v, v gs = 50% i dss ) 240 ms v p pinch - off voltage (i ds = 0.6 m a, v ds = 2 v) - 2 .5 - 1.1 - 0.5 v bv gd drain breakdown voltage (ig = 0.6 ma, source open) - 1 5 - 1 2 v bv gs source breakdown voltage (ig = 0.6 ma, drain open) - 1 3 v r th thermal resistance (au - sn eutectic attach) 7 5 c/w maximum rating (t a = 25 c) symbols parameters absolute continuous v ds v gs i ds i gsf p in t ch t stg p t drain - source voltage gate - source voltage drain current forward gate current input power channel temperature storage temperature total power dissipation 12 v - 6 v i dss 30 ma 25 dbm 175 c - 60 c - 150 c 2.6 w 8 v - 3 v i dss 10 ma @3db compression 150 c - 60 c - 150 c 2. 2 w exceeding any of the above maximum ratings will result in reduced mttf and may cause permanent damage to the device .
www.berex.com berex, inc. 1735 north 1 st street #302 san jose, ca 95112 tel. (408) 452 - 5595 september 2011 specifications are subject to change without notice. ? berex 2011 rev. 1.2 BCP060T p in _p out /gain, pae (12 gh z ) frequency = 12ghz v ds = 8 v, i ds = 50% i dss ( tune d for power) frequency = 12ghz v ds = 8 v, i ds = 50% i dss ( tune d for gain) p in _p out /gain, pae (1 8 ghz) frequency = 18 ghz v ds = 8 v, i ds = 50% i dss (tuned for power) frequency = 18 ghz v ds = 8 v, i ds = 50% i dss (tune d for gain)
www.berex.com berex, inc. 1735 north 1 st street #302 san jose, ca 95112 tel. (408) 452 - 5595 september 2011 specifications are subject to change without notice. ? berex 2011 rev. 1.2 BCP060T s - parameter ( v ds = 8v, i ds = 50% i dss ) freq . [ g hz] s11 [ mag ] s11 [ang . ] s21 [ mag ] s21 [ang . ] s12 [ mag ] s12 [ang . ] s22 [ mag ] s22 [ang . ] 1 0.92 - 57.91 13.83 142.64 0.017 62.75 0.45 - 30.63 2 0.83 - 100.13 10.45 117.12 0.032 43.42 0.34 - 49.55 3 0.79 - 129.58 7.98 99.76 0.047 34.74 0.25 - 62.90 4 0.77 - 150.61 6.32 86.33 0.061 28.79 0.19 - 72.26 5 0.77 - 165.65 5.18 75.24 0.073 27.32 0.15 - 86.36 6 0.77 - 178.11 4.35 65.56 0.084 26.36 0.13 - 101.81 7 0.78 172.13 3.69 56.72 0.094 25.99 0.12 - 123.94 8 0.79 163.81 3.25 48.59 0.103 25.03 0.12 - 137.66 9 0.80 156.81 2.88 41.33 0.108 23.59 0.12 - 155.22 10 0.81 150.09 2.58 34.01 0.114 24.54 0.14 - 169.25 11 0.82 143.11 2.34 26.33 0.120 23.14 0.16 178.07 12 0.83 136.61 2.12 18.59 0.124 22.92 0.19 168.01 13 0.85 130.15 1.94 11.44 0.130 19.85 0.22 157.74 14 0.86 123.54 1.77 3.60 0.134 16.06 0.25 148.31 15 0.88 117.87 1.60 - 4.01 0.139 14.39 0.30 140.13 16 0.89 112.39 1.45 - 11.27 0.144 10.53 0.35 132.31 17 0.90 106.79 1.29 - 19.37 0.148 7.58 0.41 126.29 18 0.91 103.05 1.13 - 26.14 0.153 6.07 0.46 120.85 19 0.92 100.04 1.00 - 32.93 0.155 3.45 0.51 115.68 20 0.92 97.13 0.88 - 38.54 0.156 0.94 0.57 111.97 21 0.93 96.22 0.76 - 43.13 0.150 0.17 0.61 109.56 22 0.93 96.46 0.66 - 46.19 0.149 0.71 0.65 107.33 23 0.92 96.55 0.57 - 49.34 0.147 - 0.34 0.68 106.11 24 0.92 97.66 0.51 - 51.56 0.145 - 0.02 0.71 106.08 25 0.94 98.95 0.46 - 53.03 0.144 2.76 0.74 105.60 26 0.93 99.53 0.41 - 54.01 0.145 3.92 0.76 106.41 note: s - parameters include bond wires. reference planes are at edge of substrates shown on wire bonding information figure below.
www.berex.com berex, inc. 1735 north 1 st street #302 san jose, ca 95112 tel. (408) 452 - 5595 september 2011 specifications are subject to change without notice. ? berex 2011 rev. 1.2 BCP060T wire bonding information using 1 mil . diameter, au bonding wires. 1. gate to input transmission line - length and height : 600 m x 250 m - number of wire(s): 1 2. drain to output transmission line - length and height : 400 m x 250 m - number of wire(s) : 1 3. source to ground plate - length and height : 250 m x 300 m - number of wire(s) : 4 disclaimer berex reserves the right to make changes without further notice to any products herein to improve reliability, function or design. berex does not assume any liability arising out of the application or use of any product or circuit described herein. life support policy berex products are not authorized for use as critical components in lif e support devices without the express written approval of berex. 1. life support devices or systems are devices or systems which (a) are intended for surgical implant into the body, or (b) support or sustain life, or (c) whose failure to perform when properly used in accordance with instruction s for use provided in labeling, can be reasonably expected to result in significant injury to the user. 2. a critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.
|
